行业新闻
浅谈转子秤的部分备件的选择、秤的使用维护
来 源：www.hfztjd.com 发布时间：2017-9-1 9:35:06
1、上下密封板转子平衡，转子精度。设备在更换备件时，应尽量安装高精度转子和上下密封板，并做到/更换，并在转子控制过程中使用上下密封板之间的间隙，减少在风中的比例。由于资金预算问题，有的公司使用转子精度不高，使用后煤炭开始出现破碎，被迫更换原来的转子，精度高，更换后出现破碎煤问题。
2、通风匹配转子秤。使用过程中包管入口管风转子秤满足三米管道速度风速校准的设计要求，风速V、V、V / 2，以平等和平等的固气压力减风率的统一，包管煤粉的正常运输。
合肥卓泰机电是专业从事：煤粉转子秤及配件、粉体转子秤、HRM立磨配件、HFCG辊压机配件、N-TGD钢丝胶带提升机配件、烟气监控的生产和销售。
3、运行期间的检查和维护转子秤。转子平衡带不能滑动，经常检查磨损情况，包管驱动轮与从动轮线速度一致。在生产过程中还可以利用机械手工具动态调节转子尺度间隙，刚打开、潮湿、着火的煤粉破碎煤可适当扩大间隙，正常生产，合理控制转子尺度间隙在20～25路。
4、传感器的检查。在运行过程中，及时检查转子秤如煤等异物，包管传感器的正常使用。5的标准校准。转子秤。在标准时间内，开罗风机在转子尺度的使用过程中，应将转子内积聚的煤炭吹出，以减少零漂现象。
1. rotor balance of the upper and lower sealing plate, rotor precision. Equipment in the replacement of spare parts, should try to install high precision rotor and the upper and lower sealing plate, and to achieve complete replacement, and rotor control in the process of using the upper and lower sealing gap between the plates, reduce in scale on the wind. Funds due to budget problems, some companies use the rotor of low precision, the use of coal began to appear after breaking, forced to replace the original rotor with high accuracy, after the replacement of broken coal problem.
Ventilation matching of 2. rotor scales. Use the process to ensure the entrance duct wind rotor scale to meet the design requirements of three meter pipeline speed calibrated by wind speed, the wind speed is V, V, V/2, to the unity of equal and equal ratio of solid to gas pressure reducing on the wind, to ensure the normal transportation of pulverized coal.
Inspection and maintenance during operation of 3. rotor scale. The rotor balance belt can not slide, often check the wear condition, and ensure the driving wheel and the driven wheel line speed is consistent. In the production process also can use the manipulator tools to dynamically adjust the rotor scale gap, just opened, moisture, ignition of pulverized coal broken coal can be properly enlarged the gap, the normal production, reasonable control of rotor scale gap in 20~25 road.
4. sensor inspection. In the process of running, timely check the rotor scales such as coal and other foreign bodies, and ensure the normal use of sensors. Standard calibration of 5. rotor scale. In the standard timing, the Cairo fan should blow up the accumulated coal inside the rotor to reduce the zero drift phenomenon during the use of the rotor scale.